< Back to the Main Site
« previous next »
Pages: [1]   Go Down

Author Topic: 12ga Steel Penetrator Rounds  (Read 3804 times)

Offline kozball

  • Steel Benefactor
  • *
  • Join Date: Jan 2011
  • Location: Papillion
  • Posts: 524
12ga Steel Penetrator Rounds
« on: February 07, 2014, 09:26:08 AM »
Logged
\"Freedom is never more than one generation away from extinction. We didn\'t pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same.\"

Ronald Reagan

Offline landon410

  • NFOA Full Member
  • **
  • Join Date: Jan 2014
  • Location: Omaha
  • Posts: 380
Re: 12ga Steel Penetrator Rounds
« Reply #1 on: February 07, 2014, 09:31:49 AM »
will that even cycle in my pump?
Logged

Offline shooter

  • NFOA Full Member
  • **
  • Join Date: Aug 2013
  • Location: near Yutan
  • Posts: 1630
Re: 12ga Steel Penetrator Rounds
« Reply #2 on: February 07, 2014, 10:22:52 AM »
 I could turn those out on my lathe!
Logged
Was mich nicht umbringt macht mich stärker
Sic semper evello mortem tyrannis
 NRA Endowment member
  Shoot  them in the crotch.  Clint Smith, thunder ranch.  Oct 14, 2016

Offline GreyGeek

  • NFOA Full Member
  • **
  • Join Date: Dec 2012
  • Posts: 1687
Re: 12ga Steel Penetrator Rounds
« Reply #3 on: February 07, 2014, 03:06:21 PM »
Is that a chunk of lead at the base of the sabot?   If so, what's to keep it from tumbling?  Does the wrapping around the sabot cause it to spin so it will be stable?
Logged

Offline landon410

  • NFOA Full Member
  • **
  • Join Date: Jan 2014
  • Location: Omaha
  • Posts: 380
Re: 12ga Steel Penetrator Rounds
« Reply #4 on: February 07, 2014, 03:32:28 PM »
how far out the shell does it protrude?
doesn't take make it a 1 shot kind of deal? how would you cycle a 2nd round of this?
Logged

Offline kozball

  • Steel Benefactor
  • *
  • Join Date: Jan 2011
  • Location: Papillion
  • Posts: 524
Re: 12ga Steel Penetrator Rounds
« Reply #5 on: February 07, 2014, 03:47:47 PM »
The youngsters at work tell me that there are some You-Tube vids.

Haven't had time to check them out yet, but said to really put a dent in plate steel.
Logged
\"Freedom is never more than one generation away from extinction. We didn\'t pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same.\"

Ronald Reagan

Offline bkoenig

  • Gun Show Volunteer
  • Powder Benefactor
  • *
  • Join Date: May 2009
  • Location: Lincoln, NE
  • Posts: 3677
  • Aspiring cranky old gun nut
Re: 12ga Steel Penetrator Rounds
« Reply #6 on: February 07, 2014, 06:12:00 PM »
I'm skeptical.  12g isn't going to have a lot of velocity, even if it does have a lot of mass.  I would think you'd have to be pretty close to the target for it to retain enough energy to penetrate an engine block.  That kind of makes it impractical for stopping a moving vehicle.

Edit:  Ok, they're claiming 1900 FPS.  I doubt if it keeps that velocity for long, though. 

« Last Edit: February 07, 2014, 06:15:33 PM by bkoenig »
Logged
Pages: [1]   Go Up
« previous next »