< Back to the Main Site
« previous next »
Pages: 1 [2]   Go Down

Author Topic: And so the addiction begins...  (Read 2675 times)

Offline bkoenig

  • Gun Show Volunteer
  • Powder Benefactor
  • *
  • Join Date: May 2009
  • Location: Lincoln, NE
  • Posts: 3677
  • Aspiring cranky old gun nut
Re: And so the addiction begins...
« Reply #20 on: November 16, 2011, 02:32:34 PM »
Probably not.  You don't really save any money by building your own, it just allows you to spread to cost out.
Logged

Offline gsd

  • 2013 NFOA Firearm Rights Champion award winner
  • NFOA Full Member
  • **
  • Join Date: Oct 2010
  • Location: Lincoln, NE
  • Posts: 1831
Re: And so the addiction begins...
« Reply #21 on: November 16, 2011, 07:40:36 PM »
ahh, the upper i am looking is a core15,

16" M4 Upper receiver with a 416R Stainless Steel 3 groove Polygonal Rifling 1:8 twist M4 Barrel, M4A3 upper receiver, Midwest Industries Gen 2 Midlength (9") 2-piece Quad Rail System, Core 15 Hardcore Billet Charging Handle V.2, M16 BCG (MPI & HP Tested), and low profile gas block.

Damned near exactly what i was looking for.
Logged
It is highly likely the above post may offend you. I'm fine with that.

Offline gsd

  • 2013 NFOA Firearm Rights Champion award winner
  • NFOA Full Member
  • **
  • Join Date: Oct 2010
  • Location: Lincoln, NE
  • Posts: 1831
Re: And so the addiction begins...
« Reply #22 on: November 21, 2011, 09:13:13 PM »
So, built the lower tonight. what i could anyway.  CMMG skimped on a takedown detent spring so i can't put the rear detent pin in until i find a replacement.  a couple questions come to mind...

I noticed the sere was a touch off, i had to file it down a touch to fit.  Problem?

Also, the select fire pin, after detent pinning, will not move from fire unless the hammer is back.  Common?

Sorry, it has been over ten years since i had any solid sort of contact with AR's.  Fired em since then yes, but ground up builds no way Nancy.

BTW, not counting the apparently continuous interruptions tonight, took me a little over an hour to build it to where it is now.
Logged
It is highly likely the above post may offend you. I'm fine with that.

Offline Dan W

  • NFOA Co-Founder
  • *****
  • Join Date: Oct 2007
  • Location: Lincoln NE
  • Posts: 8143
Re: And so the addiction begins...
« Reply #23 on: November 21, 2011, 09:47:54 PM »
Quote
Also, the select fire pin, after detent pinning, will not move from fire unless the hammer is back.  Common?

 NORMAL on all AR15's for the safety to only operate when the hammer is back
Logged
Dan W    NFOA Co Founder
Today, we need a nation of Minutemen, citizens who are not only prepared to take arms, but citizens who regard the preservation of freedom as the basic purpose of their daily life and who are willing to consciously work and sacrifice for that freedom.   J. F. K.

Offline bkoenig

  • Gun Show Volunteer
  • Powder Benefactor
  • *
  • Join Date: May 2009
  • Location: Lincoln, NE
  • Posts: 3677
  • Aspiring cranky old gun nut
Re: And so the addiction begins...
« Reply #24 on: November 21, 2011, 10:12:04 PM »
Where did you have to file?  It should just drop in.
Logged

Offline gsd

  • 2013 NFOA Firearm Rights Champion award winner
  • NFOA Full Member
  • **
  • Join Date: Oct 2010
  • Location: Lincoln, NE
  • Posts: 1831
Re: And so the addiction begins...
« Reply #25 on: November 22, 2011, 08:53:42 AM »
Dan, thanks.  i thought so, but would rather be certain.

Brian, It was only about 1/32 out of compliance, most likely paint/minor machining issues.  Couple strokes with a rat tail file and it pinned together without trouble.

BTW guys, little tidbit from an armorer buddy...the Spikes recievers are a Class 3 permit holders friend, if you get my drift.
Logged
It is highly likely the above post may offend you. I'm fine with that.
Pages: 1 [2]   Go Up
« previous next »