< Back to the Main Site
« previous next »
Pages: [1]   Go Down

Author Topic: Anti-static Mat?  (Read 2953 times)

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Anti-static Mat?
« on: November 21, 2015, 08:45:45 AM »
Anyone using an anti-static mat on their reloading bench?  I inherited a reloading press and am putting my setup together.  The bench will be in a room with carpet.  I've put down a rubber mat over the carpet where the bench will be located.  Is an anti-static mat a good idea or overkill?
Logged

Offline NENick

  • NFOA Full Member
  • **
  • Join Date: Jul 2011
  • Posts: 661
Re: Anti-static Mat?
« Reply #1 on: November 21, 2015, 09:28:06 AM »
Good idea. My reloading scales all go nuts with any amount of static. Gun powder also sticks to the inside of the plastic powder funnel. The scale also needs to be perfectly level or the platten will bind.
Logged

Offline SemperFiGuy

  • Steel Benefactor
  • *
  • Join Date: Apr 2009
  • Location: Omaha, NE
  • Posts: 2079
  • GG Grampaw Wuz a DamYankee Cavalryman
Re: Anti-static Mat?
« Reply #2 on: November 21, 2015, 09:30:02 AM »
Quote
Is an anti-static mat a good idea or overkill?

First big spark on a dry day will make it seem like a good idea.

sfg
Logged
Certified Instructor:  NE CHP & NRA-Rifle, Pistol, Shotgun, Personal Protection Inside/Outside Home, Home Firearm Safety, RTBAV, Metallic Cartridge & Shotshell Reloading.  NRA Chief RSO, IDPA Safety Officer, USPSA Range Officer.  NRA RangeTechTeamAdvisor.  NE Hunter Education (F&B).   Glock Armorer

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Re: Anti-static Mat?
« Reply #3 on: November 21, 2015, 10:17:40 AM »
Thanks, guys.
Logged

Offline Mali

  • NFOA Full Member
  • **
  • Join Date: Jan 2013
  • Posts: 1718
  • My life, my rights.
Re: Anti-static Mat?
« Reply #4 on: November 24, 2015, 02:53:38 PM »
Hoping to setup my reloading area in a couple of months. Thanks for the idea, Mud.
Logged
Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same. - Ronald Reagan

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Re: Anti-static Mat?
« Reply #5 on: November 24, 2015, 04:08:03 PM »
Quote from: Mali on November 24, 2015, 02:53:38 PM
Hoping to setup my reloading area in a couple of months. Thanks for the idea, Mud.

No problem.  Maybe I should start a Reloading Newbie thread like Unfy did when he first got started.
Logged

Offline NENick

  • NFOA Full Member
  • **
  • Join Date: Jul 2011
  • Posts: 661
Re: Anti-static Mat?
« Reply #6 on: November 24, 2015, 05:15:52 PM »
I had a primer explode once on a 223 round. I was holding the case with my finger half way over the top of the mouth. It seared my finger and would have taken an eye if I was looking down the case. It's easy the hold the tool with it pointing towards your face.

I also recently ready a story about a guy loading for a 45-70 (maybe it was on here). He forgot the crimp and the bullets started sinking deeper into each case as he fired. That cause the pressure to spike and it darn near blew his hand off.

Reloading is easy and fun, but know the little nuances of the cartridges your reloading.

/end scare
Logged
Pages: [1]   Go Up
« previous next »