< Back to the Main Site
« previous next »
Pages: [1] 2   Go Down

Author Topic: Any Kydex Holster makers here?  (Read 9521 times)

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Any Kydex Holster makers here?
« on: January 07, 2015, 08:05:55 AM »
I'm looking for someone local that can make some very simple kydex holsters..... Post if you know someone around Omaha or Lincoln that does this.


Thanks!

Logged

Offline NE Bull

  • 2011 NFOA Firearm Rights Champion Award winner
  • NFOA Full Member
  • **
  • Join Date: Nov 2008
  • Location: Lincoln, NE
  • Posts: 3501
    • A "friend's" blog
Re: Any Kydex Holster makers here?
« Reply #1 on: January 07, 2015, 08:31:30 AM »
There is a fella out of LaVista that I contacted about a custom holster, but I can't seem to find his FB post.
Looked like quality work.  Another fella around York- LEO, but can't find his either, and Kearney that I can find, but that's a ways out.  I'll do some more searching.
Logged
“It is not an issue of being afraid, It's an issue of not being afraid to protect myself.”
 Omaha Mayor Jean Stothert
 "A gun is a tool, Marian; no better or no worse than any other tool: an axe, a shovel or anything. A gun is as good or as bad as the man using it. Remember that."  Shane

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Re: Any Kydex Holster makers here?
« Reply #2 on: January 07, 2015, 08:38:44 AM »
I've made a few and have a press.  Time is my biggest limiting factor.
Logged

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #3 on: January 07, 2015, 08:52:28 AM »
I have been doing some also. I am in North Lincoln. I am like Mudinyeri I have a press so depending on what you want I might be limited. If my dang phone didn't die this morning I would post a picture of the holster I just made for my 17.
Logged

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Re: Any Kydex Holster makers here?
« Reply #4 on: January 07, 2015, 08:56:33 AM »
What I am looking for basically is someone who has some thin kydex and knowledge of working with it........ I want to buy some thin kydex sheath's (yes more like a sheath) to store my pistols in that then get put in padded range bags. Just trying to prevent sights from getting dinged up and knocked around when I fly with them.

Nothing fancy, just functional.....


Thoughts?
Logged

Offline NE Bull

  • 2011 NFOA Firearm Rights Champion Award winner
  • NFOA Full Member
  • **
  • Join Date: Nov 2008
  • Location: Lincoln, NE
  • Posts: 3501
    • A "friend's" blog
Re: Any Kydex Holster makers here?
« Reply #5 on: January 07, 2015, 09:03:46 AM »
A couple of us from work made range bag inserts from some plastic foam like stuff, then cut out what we needed for the pistols and mags.  but it might not be the best as far as space savings for flying.... 
Logged
“It is not an issue of being afraid, It's an issue of not being afraid to protect myself.”
 Omaha Mayor Jean Stothert
 "A gun is a tool, Marian; no better or no worse than any other tool: an axe, a shovel or anything. A gun is as good or as bad as the man using it. Remember that."  Shane

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #6 on: January 07, 2015, 09:04:54 AM »
Get a hardcase?



This is one i made for a friend. Do you want something that will just go over the slide?
Logged

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Re: Any Kydex Holster makers here?
« Reply #7 on: January 07, 2015, 09:05:01 AM »
Quote from: NE Bull on January 07, 2015, 09:03:46 AM
A couple of us from work made range bag inserts from some plastic foam like stuff, then cut out what we needed for the pistols and mags.  but it might not be the best as far as space savings for flying.... 



"Saving Space" is critical on packing.... :-) I'm taking five pistols to matches with me and a lot of magazines 
Logged

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Re: Any Kydex Holster makers here?
« Reply #8 on: January 07, 2015, 09:06:23 AM »
Quote from: tstuart34 on January 07, 2015, 09:04:54 AM
Get a hardcase?



This is one i made for a friend. Do you want something that will just go over the slide?

Five pistols packed tightly inside a Pelican case (each in their own small range bag). Yes need to cover the entire slide so the rear sight is protected too
Logged

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #9 on: January 07, 2015, 09:08:21 AM »
What about some Kydex just molded around sights and slide? Clips on and clips off?
Logged

Offline on the fritz

  • NFOA Full Member
  • **
  • Join Date: Jan 2013
  • Posts: 212
Re: Any Kydex Holster makers here?
« Reply #10 on: January 07, 2015, 09:08:48 AM »
Ryan @ 402kydex.com might be able to give you what you want. 

Tell him Fritz sent you.  I have seen his work and it's top notch.  He's in Lincoln.  I don't have any more contact info other than his website right now.  He's out until Jan 12th. 
Logged

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Re: Any Kydex Holster makers here?
« Reply #11 on: January 07, 2015, 09:14:03 AM »
Quote from: tstuart34 on January 07, 2015, 09:08:21 AM
What about some Kydex just molded around sights and slide? Clips on and clips off?

Yep something that takes up a very minimal amount of space
Logged

Offline Chris Z

  • NFOA Co-Founder
  • *****
  • Join Date: Dec 2007
  • Location: Lincoln NE
  • Posts: 2496
    • Nebraska Concealed Carry Training
Re: Any Kydex Holster makers here?
« Reply #12 on: January 07, 2015, 09:14:18 AM »
Quote from: on the fritz on January 07, 2015, 09:08:48 AM
Ryan @ 402kydex.com might be able to give you what you want. 

Tell him Fritz sent you.  I have seen his work and it's top notch.  He's in Lincoln.  I don't have any more contact info other than his website right now.  He's out until Jan 12th. 



Thanks!
Logged

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #13 on: January 07, 2015, 09:31:59 AM »
Quote from: Chris Z on January 07, 2015, 09:14:03 AM
Yep something that takes up a very minimal amount of space

This is do able Chris. I send me a PM or a e-mail tstuart34@gmail.com if your interested. Like I said my DOA this morning so thats the best way to get me right now.
Logged

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Re: Any Kydex Holster makers here?
« Reply #14 on: January 07, 2015, 09:49:55 AM »
Here's a basic knife sheath that I did a while back. 



... and a basic holster that I did (MOLLE clip on the back)









Could easily do something along either of those lines.
Logged

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #15 on: January 07, 2015, 10:01:39 AM »
Mud

What type of press are you using?
Logged

Offline Mudinyeri

  • God, save us!
  • NFOA Full Member
  • **
  • Join Date: May 2010
  • Location: Omaha
  • Posts: 3965
  • Run for the Hills
Re: Any Kydex Holster makers here?
« Reply #16 on: January 07, 2015, 11:49:06 AM »
Logged

Offline gsd

  • 2013 NFOA Firearm Rights Champion award winner
  • NFOA Full Member
  • **
  • Join Date: Oct 2010
  • Location: Lincoln, NE
  • Posts: 1831
Re: Any Kydex Holster makers here?
« Reply #17 on: January 07, 2015, 12:42:05 PM »
What about a shroud of sorts that just covers the slide? Retention tab could be inside the trigger guard...
Logged
It is highly likely the above post may offend you. I'm fine with that.

Offline tstuart34

  • NFOA Full Member
  • **
  • Join Date: Oct 2013
  • Location: Lincoln
  • Posts: 885
Re: Any Kydex Holster makers here?
« Reply #18 on: January 07, 2015, 01:00:08 PM »
Quote from: gsd on January 07, 2015, 12:42:05 PM
What about a shroud of sorts that just covers the slide? Retention tab could be inside the trigger guard...

That's exactly what i was thinking....
Logged

Offline unfy

  • Lead Benefactor
  • **
  • Join Date: Jun 2010
  • Location: TN (was La Vista, NE)
  • Posts: 1830
  • !!! SCIENCE !!!
Re: Any Kydex Holster makers here?
« Reply #19 on: January 07, 2015, 10:01:20 PM »
I'd second Mud.  He knows his stuff.

I've formed replacement kydex for my crossbreed - and it's not a terribly difficult process.

But I wouldn't suggest myself for making other folk's stuff :).  I just one offed my own thing.
Logged
hoppe's #9 is not the end all be all woman catching pheramone people make it out to be ... cause i smell of it 2 or 3 times a week but remain single  >:D
Pages: [1] 2   Go Up
« previous next »